Searching...

Matching results

    How-to Video Series

    The How-to Video Series is a set of tutorials designed to help new users to perform the key operations on AirVantage’s web user interface.

    You should be able to perform the selected operation on your own by following the instructions in these videos. To keep the content simple, we have included only the basic instructions; for more details, please refer to the User Guide. You may not find the tutorial illustrated with the hardware type you use, however, the principles of the AirVantage operations should apply to other hardware types.

    Initializing Table Of Contents...

    How to Work With and Create Driver Behavior Reports

    The Driver Behavior report describes the behavior of your fleet in terms of driving-related incidents over the course of the reporting period. The report tracks the following incidents: Hard Accelerations Hard Decelerations Cornering Speeding Driver behavior reports require inertial sensors on the router (as supported on the MP70 and XR series), and will not be reported on an AirLink GX450 or LX60. Incidents are triggered by exceeding configured (hard acceleration, hard deceleration, cornering) or posted thresholds (speeding) at the given location at the time of the incident.

    Read More...

    How to Work With and Create Trips Reports

    The Trips report provides a series of views that display the location of selected devices and shows the route that they have taken based on GPS data, for a selected time frame. The Trips report plots the devices’ location as a continuous line on the map. This report is most useful for a single AirLink router over a relatively short period of time (for example, one gateway trip) and can be used to validate where a device was, and determine its behavior at a specific point in time.

    Read More...

    Once a system is registered, you can use AirVantage to monitor and configure it remotely. Follow this tutorial to learn about basic configuration parameters, and how to apply them via a template. To watch the video version, click on the screen above. Or, if you prefer, follow the steps below at your own pace. 1 / Basics 2 / Templates This tutorial assumes that you have already seen how to register your device with AirVantage on the Register page.

    Read More...

    How to create a new alert rule?

    Alert rules are configured from the Alert Rules section. For more information, see What is an Alert Rule? Configure Rules Alert rules are defined from the Configure activity, in the Alert rules section. Here, we can see all the alert rules created for the company’s sytems, and their status. We can activate, deactivate or edit the rules here. Display this screen, then click on the + (plus) button to add a new alert rule.

    Read More...

    How to manage a large number of systems?

    AirVantage is a centralized console designed to manage a large number of systems. Follow this tutorial to learn how to use of filters, labels and sorting methods to manage your entire fleet, or specific groups of systems. To watch the video version, click on the screen above. Or, if you prefer, follow the steps below at your own pace. 1 / Filters 2 / Labels 3 / Sorting Managing your fleet (hundreds or even thousands of gateways) can quickly become time-consuming if your management tool has not been designed for large deployments.

    Read More...

    How to remotely change the ACEmanager password on my ALEOS Gateway?

    This functionality only applies to devices using MSCI to communicate with ALMS: MP, RV, GX, LS and ES devices from ALEOS firmware version 4.4.0 and onwards Raven, MP, PinPoint on firmware version 4.0.11 or later For devices that communicate with ALMS using LWM2M, the password field is no longer required. In this case, you can skip to Change the ACEmanager password for one device. The M3DA password will still be required for AAF applications.

    Read More...

    How to retrieve device data in a dataset?

    AirVantage allows you to retrieve firmware data from your AirLink gateways. Follow this tutorial to learn how to create datasets to retrieve the firmware parameters from your gateways, and how to use the scheduling functionality to automate the operation. To watch the video version, click on the screen above. Or, if you prefer, follow the steps below at your own pace. 1 / Create 2 / retrieve 3 / Use Step 1: Create Dataset In AirVantage terminology, a “Dataset” is a list of ALEOS parameters that a user would like retrieved from their gateways.

    Read More...

    How to upgrade firmware on my ALEOS gateways?

    You can upgrade the firmware on a single device or in bulk. The operation will handle the upgrade of the firmware as well as the radio module: if new radio module firmware is available, it is included with the ALEOS firmware package. Please watch this video tutorial for an overview. Identify the systems to upgrade Click on Monitor > Systems to view the list of your deployed AirLink Gateways The you will need to select one or several Systems from the list to be upgraded.

    Read More...

    TOP